P/N 9925220 Rev 01 08/14 Page 1 of 5
BEFORE YOU BEGIN
Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
P/N 2880267
GLACIER PRO PLOW FRAME
EXTENSION KIT
APPLICATION
FOR USE WITH THE GLACIER PRO MID SIZE PLOW FRAME (P/N 2880260)
23
9
3
5
20
13
19
6
15
7
21
22
20
5
6
2
10
11
16
1
8
14
17
6
12
18
4
NOTE: This extension kit is recommended when the prospector track system is installed on the unit.
P/N 9925220 Rev 01 08/14 Page 2 of 5
TOOLS NEEDED
15mm and 17mm Sockets and Wrenches, Long Nose Pliers
APPROXIMATE ASSEMBLY TIME
30 mins.
IMPORTANT
Your Polaris GLACIER PRO PLOW FRAME EXTENSION KIT is exclusively designed to work with
the Mid-Size Glacier Pro Plow system (P/N 2880260) for your vehicle. Please read the installation
instructions thoroughly before beginning. Installation is easier if the plow system is clean and free of
debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly
in the sequence shown.
Spare Kits
Ref Description
Plow Extension
Kit (2880267)
Plow Extension
Hardware Kit
(2205547)
Winch Link Kit
(2205542)
1
Cotter Pin-Ø3X25mm 2x
2x
2
Flat Washer-M6 ID 6.4XOD 12X1.6 1x
1x
3
Hexagonal Bolt-M10-1.5X65 2x
2x
4
Hexagonal Bolt-M6-1.0X20 2x 2x
5
Hexagonal Flange Bolt-M10-1.5X45 2x 2x
6
Hexagonal Flange Nylon Nut-M10-1.5 5x 5x
7
Hexagonal Nut-M12-1.75 1x 1x
8
Hexagonal Nylon Nut-M6-1.0 2x 2x
9
Hexagonal Nylon Nut-M10-1.5 1x 1x
10
Lock Washer-M6 ID 6.1XOD 11.8X1.6 1x
1x
11
Socket Head Cap Screw-M6X1X18mm 1x 1x
12
Kickstand Spring 1x 1x
13
Extension Clamp 1x 1x
14
Cap 1x 1x
15
Kickstand Shoe 1x 1x
16
Clevis Pin-Ø16mmX40mm 2x 2x
17
Compression Spring 1x
1x
18
Pedal Support 1x 1x
19
Extension Welded Frame 1x
20
Extension Sleeve 2x 2x
21
Extension Kickstand 1x 1x
22
J Rod 1x 1x
23
Extension Winch Link, Mid-Size 1x 1x
Instructions (P/N 9925220) 1x
P/N 9925220 Rev 01 08/14 Page 3 of 5
INSTALLATION INSTRUCTIONS
IMPORTANT: Polaris winch must be installed rst. It is strongly suggested that your UTV suspension
setup is at the stiffest rating for the front suspension
PUSHFRAME EXTENSION:
1. Position pushframe (P/N 2880260) under the extension as shown on gure below. Insert two frame sleeves
(20) inside the rear mounting holes of the frame. Fasten the extension using hexagonal ange bolts
M10-1.5 x 45mm (5) and hexagonal nylon nuts M10-1.5 (6).
2. Position and fasten extension clamp (13) using hexagonal bolts M10-1.5 x 65mm (3) and hexagonal ange
nylon nuts M10-1.5 (6).
20
13
3
5
6
6
P/N 9925220 Rev 01 08/14 Page 4 of 5
HOOK-UP EXTENSION ASSEMBLY:
Refer to the mount plate installation guide for complete details.
WINCH LINK ASSEMBLY:
Change the winch link for the new longer winch link (23) and new nylon nut (9) supplied with the extension kit.
Refer to the mount plate installation guide for the correct link adjustment procedure.
23
9
16
1
NOTE: Kickstand of pushframe is not used once the Extension is installed.
NOTE: Use procedure mentioned in mount plate kits concerning height adjustment of the kickstand and auto
retract-stand adjustment for adjustment of extension kickstand.
P/N 9925220 Rev 01 08/14 Page 5 of 5
Winch Link Kit (2205542)
Hardware Kit (2205547)
9
23
14
6
17
22
12
1
16
21
4
18
16
8
1
2
10
11
6
5
20
6
20
5
6
13
3
15
7
See table on page 2 for a complete part description.