ARDEX 8+9
™
Rapid Waterproofing and Crack Isolation Compound
Description and Usage
ARDEX 8+9
™
Rapid Waterproofing and Crack Isolation
Compound is a best-in-class, two-component, solvent-free,
cement-based membrane. Comprised of an acrylic-based
liquid compound and a Portland and other hydraulic
cement-based powder, ARDEX 8+9 can be applied easily
with a paint roller or a brush to produce a highly flexible,
waterproof coating. This coating protects from topside
water infiltration and provides an excellent bonding layer
for ARDEX tile and stone mortars. When properly installed,
ARDEX 8+9 reduces the risk of efflorescence and is IAPMO
certified for use as a shower pan.
ARDEX 8+9 can be used for topside waterproofing of all
common building substrates including showers, balconies
and other wet areas. On interior applications, ARDEX 8+9
can be used over concrete and masonry finishes, existing
tile, drywall, cementitious backer boards and plywood on
all interior floors or walls prior to the installation of tile and
stone.
+
Contact the ARDEX Technical Service Department
for guidance on exterior applications. ARDEX 8+9 also is
ideal for crack isolation up to 1/8” (3 mm) when used with
ARDEX SK MESH
™
Reinforcement Fabric for Waterproofing
and Crack Isolation; 1/16” (1.5 mm) when used alone.
Substrate Preparation
All substrates must be structurally sound, solid, dry,
thoroughly clean and free of oil, wax, grease, asphalt,
latex and gypsum compounds, curing compounds**,
sealers and any contaminant that might act as a bond
breaker. Plywood substrates must be APA-rated, Type 1
exterior-grade plywood. Refer to ANSI A108 AN-2 “General
Requirements for Subsurfaces,” the Tile Council of North
America’s “Handbook for Ceramic Tile Installation” and
TTMAC for detailed information on surface preparation
and guidelines for substrate construction. The plane of
wall surfaces must be plumb and true. Floor surfaces
must have minimal variation in the plane or slope, and
sloped areas must have proper slope towards the
drain(s).Should interior pre-leveling or substrate
repair be required, use:
Product Interior Exterior Vertical Horizontal
ARDEX AM 100
™
Rapid
Set Pre-Tile Smoothing
and Ramping Mortar
(only on cementitious
substrates)
X X X X
ARDEX A 38
™
Rapid Set
Screed
X X X
ARDEX A 38 MIX
™
Rapid
Set, Premixed Screed
X X X
ARDEX Liquid
BackerBoard
®
Self-
Leveling Underlayment
(for wood and concrete
subfloors)
X X
ARDEX TL 1000
™
Tile
Leveler, Self-Leveling
Underlayment
X X
ARDEX TL PATCH
®
Tile
Leveler, Underlayment
Patch and Skimcoat
X X X
Expansion joints must be provided over existing moving
joints, and where substrate materials change composition
or direction, per ANSI A108 AN-3.7 and TTMAC guidelines.
**Note on Curing Compounds
Test areas of ARDEX 8+9 can be installed and evaluated
over concrete slabs that have been treated with either
silicate or acrylic resin curing compounds. These
compounds must be installed in strict accordance with
the compound manufacturer’s written recommendations.
If a silicate type has been used, all residual salts must
be removed.
Please be advised, however, that there are a number
of curing compounds sold today that are wax- or
petroleum-based emulsions. These are permanent bond
breakers that must be removed completely prior to
patching or leveling. Dissipating compounds must also
be removed completely by mechanical means prior to
installing any ARDEX material.
It is imperative to be able to determine the type of curing
compound that was used before proceeding. Any curing
compound that cannot be identified should be completely,
mechanically removed.
Recommended Tools and Accessories
ARDEX M-6W Mixing Bucket***, ARDEX T-2 Ring Mixing
Paddle, ARDEX SK MESH, ARDEX SK DRAIN
™
Mesh
Reinforcement Fabric for Drain Tie-Ins, 3/16” x 3/16”
V-Notch Trowel, high speed drill, margin trowel, putty
knife, 3/8” nap paint roller and paintbrush
***When mixing commercial-sized units of ARDEX 8+9,
a minimum 6-gallon capacity is needed. ARDEX
recommends the ARDEX M-6W Mixing Bucket for
this purpose.
Mixing and Application
ARDEX 8+9 can be mixed to two different consistencies
– caulking or paintable. Using the mix ratios below, pour
the ARDEX 8 liquid into the mixing bucket first, and then
add the ARDEX 9. Do not add water or additives! For
best results, mix with an ARDEX T-2 Ring Mixing Paddle
and a high speed drill for 2 - 3 minutes. Just prior to
application on the substrate, the mixture should be stirred
again to ensure a creamy, smooth, lump-free consistency.
Caulking Consistency
• For one 9 lb. (4 kg) bag of ARDEX 9,
use approximately 2/3 of the 1 gallon unit
(approximately 2/3 gallon / 2.5 L) of ARDEX 8.
• For one 27 lb. (12 kg) bag of ARDEX 9, use
approximately 2/3 of the 3 gallon unit
(approximately 2 gallons / 7.56 L) of ARDEX 8.
• To mix small batches of the caulking consistency, mix
one 2/3 part of ARDEX 8 with one part of ARDEX 9
powder by volume.